Edimax EW-7317UHg Bedienungsanleitung

880022..1111gg HHII--GGaaiinn WWiirreelleessss LLAANN UUSSBB AAddaapptteerr User Manual Version: 1.0 (

5 II. Install the USB Adapter A. Plug the USB Adapter into the USB port of your computer. B. The “Found New Hardware Wizard” is displayed, select “I

6 D. Click “Finish” to complete the installation. III. Using the Configuration Utility To setup the USB adapter, double-click the icon in the sys

7 First Way A. Double-click the utility icon in the system tray. B. Click “Yes” to use the utility of the USB adapter. Second Way A

8 3 Configuration Utility The Configuration Utility is a powerful application that helps you configure the 802.11g HI-Gain Wireless LAN USB Adapter a

9 Parameter Description Mode Station – Set the USB adapter a wireless client. Access Point – Turns the USB adapter to function as a wireless AP.

10 Parameter Description Signal Strength This bar shows the signal strength level. The higher percentage shown in the bar, the more radio signal be

11 Parameter Description Tx Rate There are several options including Auto/1/2/5.5/11/6/9/12/18/24/36/48/54Mbps for you to select. When th

12 Parameter Description Authentication Mode This setting has to be consistent with the wireless networks that the adapter intends to connect. Open

13 3.3 WEP and WPA Encryption WEP is an data encryption algorithm, which protects Wireless LAN data in the network against eavesdropping. WEP has b

14 Parameter Description Key1 ~ Key4 The keys are used to encrypt data transmitted in the wireless network. Fill the text box by following the rule

COPYRIGHT Copyright © 2004/2005 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed,

15 Parameter Description Connect Information It is the setting for WPA mode. Protocol This adapter supports two kind of protocol for au

16 Parameter Description WEP Key If the AP uses WEP data encryption function, please clcik “WEP KEY SETTING“ to setup the WEP key. WEP K

17 Parameter Description Power Consumption Setting Continuous Access Mode (CAM) – The adapter will always set in active mode. Maximum Power-Saving

18 3.5.1 AP Connection Status Parameter Description Mode Station – Set the USB adapter a wireless client. Access Point – Turns the USB adapter t

19 3.5.2 AP General Connection Setting Click “More Setting”, users are allowed to setup the AP connection setting, Encryption Setting and other adv

20 Parameter Description Tx Rate There are several options including Auto/1/2/5.5/11/6/9/12/18/24/36/48/54Mbps for you to select. When th

21 Parameter Description Fragement The value defines the maximum size of packets, any packet size larger than the value will be fragmented. If you

22 Parameter Description Filter Type Disable – Disable the MAC Address filter function. Accept – Only the wireless adapters with the MAC Address se

23 4 Troubleshooting This chapter provides solutions to problems usually encountered during the installation and operation of the adapter. 1. Wha

24 5. What is Infrastructure？ An integrated wireless and wireless and wired LAN is called an Infrastructure configuration. Infrastructure is applic

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital de

25 12. What is DSSS？What is FHSS？And what are their differences？ Frequency-hopping spread-spectrum (FHSS) uses a narrowband carrier that changes fre

R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL

CONTENTS 1 INTRODUCTION...1 1.1 FEATURES ...

1 1 Introduction Thank you for purchasing the 802.11g Hi-Gain Wireless LAN USB Adapter. This USB Adapter is designed to comply with IEEE 802.11g Wir

2 • Transmit Power: 20dBm (Typical) • Signal Range: Indoors: Up to 500 ft (150 meters), Outdoors: Up to 2100 ft (650 meters) • Dimension: 120(H) x

3 2 Installation Procedure Before you proceed with the installation, please notice following descriptions. Note1: Please do not install the USB ad

4 C. Click “Continue Anyway” to finish the installation.